特徴
本商品は、従来の物理的手法に変わる新しい金属表面処理方法で、入り組んだ細部に渡り均一に処理することができる化学処理剤で比較的安全な薬品構成になっていますので取扱易く一度に大量の製品を均一に短時間で仕上げることができます。
Characteristic
This is a new surface treatment
agent for metal which substitute or supplement conventional
physical methods.
This agent can workk on intricate surface on metal sevenly with
chemical reaction. Its component is consisted of relatively
safe chemicals.
It is easy to handle and can process a large number of work
pieces at a time and uniformly in a short period of time. |
主成分
・ 無機酸を主成分とした比重1.651の酸性液体。
・ 薄い黄色で特有の刺激臭がする。
・ 普通物(毒劇物指定外品)
Principal component
・ Acidic liquid, mainly composed
of Inorganic acid with 1.651 specific gravity
・ Pale yellow, with particular irritating odor
・ Common material ( not esignated as toxic and dangerous substances) |
対象金属
Cu系合金及びフェライト/マルテンサイト系でNiを含まない400番台で主成分がFe3極合金であるもの。
Materials
to be treated
Carbon Steel
and 400 series ferrite, mar-ten-site SUS which does not include
Ni and with main components of ferrous 3 axis alloy
|
用途
・ 金属表面に発生した切削加工焼けの除去。
・ ミクロン単位の微細なバリを選択的に溶解し除去。
・ 鋭角エッジ部の面取。
・ Cu合金表面の平坦化による光沢出し。
Applications
・ To remove the burn on metal surface
after cutting.
・ To dissolve and remove the microscopic metal burrs selectively.
・ To chamfer the sharp angled edge
・ To make CU. alloy surface flat and therefore shinny |
処理前準備
・ 保護用具を身に付け緊急の場合に備えて水道設備の有る場所を選び、更に、処理剤及び金属処理中に刺激臭が発生するので排気 設備も備わった箇所を準備する。
・ 処理剤を耐薬品性の容器に適量移し替え液温が25〜30度の範囲に成るよう加温及び冷却する。(SUS容器など金属製品は 使用しないで下さい)
・ 処理時間を事前にテストピースを使い条件出しを実施する。
・ 処理する製品を脱脂洗浄し切削液等が処理剤に混入しないようにする。
Preparation
・ Wear protective gear. The operationg
place shoould be equipped with plumbing for emergency use, and
ventilation system as irritationg gas arises during operation.
・ Transfer the liquid from container to a chemical resistant
vessel (metal vessels like SUS container unusable).
Arrange the chemical emperature between 25 ℃ー30℃.
・ Decide the treatment time by means of the trial experiment
on test samples.
・ Degrease the work pieces in order to prevent impure substances
like cutting fluid from mixing into the surface treatment agent. |
使用方法
・ 製品同士が重ならないように専用トレーにセットする。
・ 処理液槽に製品を決められた時間、浸透し処理を行う。
・ 処除去するバリの大きさによって異なるがおおよそ5分〜10分間です。
・ 処理中は定期的に軽く製品を液中で振ってください。
・ 処理が終わったなら充分に液切りを行い水の入った槽で製品に付着した処理剤を濯ぎ洗う。
・ 二連の水洗槽で順に製品を洗浄する。
・ 純水の温水による超音波洗浄で製品を洗浄。
・ 製品をエアーブローで乾燥させ終了。
How to use
・ Set the work pieces on a tray
by separationg each other with the same space so that they do
not touch.
・ Soak the wok pieces int the processing tub for the designated
time.
・ The time of soaking varies according to the degree of oxidized
film. The average time is about from 5 to 10 minutes.
・ Shake the work pieces lightly at regular intervals in the
liquid during the treatment.
・ When the treatment has finished, please drain the lliquid
fully and rinse the work pieces in a water tub.
・ Clean them in double water tubs consecutively.
・ Clean them with pure water in a super sonic cleaner.
・ The final course is to dry the work pieces by air blow.
使用例・処理例の詳細はこちら
|
貯蔵方法
・ 容器の蓋をしっかり締め、直射日光の当たらない冷暗所に保管してください。
・ 他の薬品及び有機物から離して下さい。
・ 保管場所には鍵をかけて下さい。
How to store the
chemical
・ Tight-fit the lid
of the containers. Store them in a cool place avoiding direct
sunlight.
・ Keep them away from other chemicals or organic matters.
・ Lock the storage site. |
老廃液再生方法
・ 新液の入っていた元の容器に20〜25kg程度入れ専用キャップ(赤色)を締め当社にお送り下さい。
・使用直後の老廃液は絶対に容器に移さない充分に冷えてから作業を行って下さい。
How to recycle the waste liquid
・
Please send back the waste liquid to us after putting the liquid
back into the original canteen up 20〜25 kg with the red cap
tightly closed.
・ Do not move the waste liquid immediately after the liquid
wase used and make sure that the liquid emperature has cooled
down. |
廃棄処理
・処理効果のなくなった液は、水で充分に希釈した後中和剤にて中和処理後、産廃業者へ廃棄委託して下さい。
Disposal
・ Waste liquid must be dilutd with a large
amount of water and neutrallized with neutralizing agent.
Have the neutralized contaminant disposed of by a industrial
waste disposal contractor |
処理薬品注意事項
・別添付製品安全データーシートをご確認下さい。
Cautions
on the processed liquid
・ Please
see the attached material safety data sheet.
|
製造元
福井県鯖江市丸山町2-4-7
TEL0778-51-7155 / FAX0778-51-7440
工業薬品の製造『登録番号井16号』
工業薬品の販売『登録番号263号』
株式会社 北 陸 濾 化
Manufacturer
2-4-7, Maruyama-cho,Sabae, Japan
Tel 0778-51-7155 / Fax 0778-51-7440
Certification of industrial chemical production (registered
No.16)
Certification of inustrial chemical sales (registered No.263)
HOKURIKU ROKA CO., LTD |